Impulsive Sewing Project: Design-It-Yourself Tunic

IMG_5310

I’ve been getting antsy to take a break from my (many…many…MANY) current projects in order to make something cute and comfy for myself. I decided at about 9pm tonight to start something! That usually leads to disaster, but so far, it’s going great!

I decided to use one of my vintage sheets because it’s soft and I liked the retro print for the tunic style. (The shirt I’m making is the red one up in the left corner.)

The idea behind Design-It-Yourself Clothes is that you draft your own patterns from your measurements or from existing clothing, making changes to design new styles for your body. I’d already used the book and some internet resources to make my perfect tee pattern. I used that pattern as a guideline for this shirt.

IMG_5316 I lined my pattern up along the centerfold, adding about an extra 2 inches to create the gathers at the waist. I also decided to use the hem of the sheet as the hem of my shirt. It won’t round up at the sides, but I really don’t know how much that matters. As you can see, it only makes about a half an inch difference.

                   IMG_5319 IMG_5320

I then marked where the placket should go. (Placket??? New to me… it’s basically where the buttons go. Google it if you want a better definition 🙂 ) I went ahead and marked this on my pattern in case I decide to make this  shirt again.

This is where it gets tricky. The book gives very unclear directions for a lot of steps. They understandably assume that if you’re ready to design your own patterns, then you’ve obviously made many a placket in your day. So, there was not really an explanation for creating said placket, at least not one that I could really understand. So I felt my way through that one. I had to cut 3 different versions before I even came close. The one pictured above is wrong. It’s just the scraps from the shirt and was way too small. You need, as far as I can tell, 2 strips that are about 2 inches long than the opening and about twice the width of the opening if the front was unfolded. shirt Here’s a really crappy drawing to illustrate. Just pretend the lines are straight and that it was not done in a hurry at 11:30 pm. The dotted lines indicate that you will fold there, or that you have cut those placket pieces on the centerfold.

Next I cut out my back using my tee pattern. This time I cut right on the fold, because I didn’t want any extra material in the back.IMG_5327

Then I pinned my shirt together from the outside and tried it on. That hurt a little… I guess not every pin was pointing out 🙂 But I figured if I could slip it on with pins in it, then getting it on without them would be a breeze. I forgot to take pix as I pinned it and sewed it, but here is a picture of it put together before sewing: IMG_5328 I sewed the placket sides first, starting with the left side (if the shirt was on). This is the side with the buttons. Then I sewed the side with the button holes. I did it in this order because you’ll want the button hole side to overlap the side with buttons.IMG_5332 Then I created the gathers by sewing across the edge and pulling the threads. Then I folded the bottom of the placket pieces under and overlapped them the way they needed to be. I pinned it all together and then top stitched the bottom. Tomorrow I will actually topstitch around the rest of the placket, but it was just necessary to get this part done. This was probably the hardest part, because it requires a lot of agility. it’s a small space and a lot of overlapping bits that want to slide around. Also, you want to make sure you have enough overlap for those buttons and button holes. I barely did, but I was afraid if I made it any tighter, the shirt would be uncomfortable.

Then I easily sewed the side seams and shoulder seams. This is where I decided to stop, because all that’s left are the sleeves and the collar. I want to think about what sleeves I want. I’m leaning toward a loose 3 quarter length with slight gathers at the shoulders, but I’m also really tempted to do sleeveless.

Here’s the shirt on my duct tape double:IMG_5332 There’s a lot of extra room around the neckline. The neckline will curve when I’m done with it, so hopefully that will take out some of that bulk. Also, I’m going to do a little work to the back which should also help. but I’m really pleased with the front view!

IMG_5335 From the side, it’s annoyingly shapeless. But I’m very small on top and my butt sticks out. so that happens 😦 I’m hoping that by making darts in the area indicated in red that the fit will be more flattering.IMG_5337 It’s not bad from the back either, but once again, it could benefit from some reduction in the upper back.

At any rate, I’m very happy with how it’s turned out. Especially for a spur of the moment decision 🙂

2 thoughts on “Impulsive Sewing Project: Design-It-Yourself Tunic

  1. Great project! I actually love that fabric. You are so creative!! I wish I could use stuff around the house, which I don’t really have much of a collection now!! I always want to buy buy buy fabric!!! But the print really is very cute. And I love it on that style of shirt!! I can’t wait to see it on yoU!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s